Learn more about the trades we cover.
Builderscrack has a fresh approach to finding great fabricators. You tell us what you need done and we tell our trusted independent tradies about your job. In no time you've got great pros to choose from.
To see tradespeople and reviews in your area, select your district below.
Check out how homeowners like you are using Fabricators on Builderscrack to build, repair and improve their homes right now.
We have an ornate looking mailbox that got hit so the metalwork holding it up snapped, hoping to find someone to weld it securely to the post and save us digging out the concreted post
Read moreWe have a set of stainless steel steps that are no longer used but would like to have a couple of stainless plates made for the corners of our house in the driveway so wondering if we can make use of the stainless we have?
Read moreNeed to increase the height of metal railing by 200.
Read moreWanting to see if a rotary clothes line arm can be welded back on as it has come off at our tenants house. Probably be easier to do onsite.
Read moreHi my fabrication shop have 16 x steel caster table frames to have powdercoated black. They are 2000mmx900mmx1000mm Made of 50mmx50mmx3mm steel SHS (mill finish) with a bits of angle iron welded in the bottom section of frame to support a recessed shelf and caster plates in bottom corners to mount casters too. I have attached a rough sketch, but bear in mind the frames will likely have 2 extra vertical posts in the middle and one extra horozontal bar in the middle of table top....
Read moreRust in gate as per photos and rejoin spikes and powder coat again
Read moreI need a concession window for my food truck. Just want to cut a window section out and add gas struts to the cutout, so I can flip window up for a concession window.
Read moreQuotes for x3 bar chairs needing to be coated in black or copper please.
Read moreTo provide quotation and lead time to frame the steel stud for 19 rooms in a 4 level building. Estimated total size: 500m2. Targeted to start on end of Feb/ early March.
Read moreWe require someone to install and fit a handle ( drill out some holes) & repair a latch on a aluminium roof top tent ( attached to a vehicle). We have sent all the parts to the customer required to fix. What you will need: You will need hammer, drill & metal drill bits and a rivet gun Step 1: Put 3rd rivet into the damaged latch hook. Once done use a hammer to bend the latch hook back into the correct latch position. Step 2: Replace latch bolt, one of the latch bolts was damaged in transi...
Read moreNeed to design, make and install a bracket to hold up a sliding gate motor off the ground ASAP. Current bracket made not suitable for motor weight and also not correct height (photo 1). Will need to be put on a concrete pad and coming up rather than bolted on side of driveway as shown in picture of current bracket....similar to something in photos 2, 3 and 4 (I think)!
Read moreTo whom it may concern, I am looking for a job that can be done by a Panel Beater it is for my car a 2001 wrx Subaru and am looking to get it fixed. Thought I would give this a try to see what's around, if you can do this job for me please message me privately or give me direct contact with you to discuss further more. I have attached photos down below for reference. Kind Reagards,
Read moreWelding and making new steel upright for existing frame. As this very old structure we need to keep as was so need to extend frame to end so no one can fall off landing.
Read moreCaravan nearly failed it's warrant due to crack in metal framing underneath caravan body. Access is relatively easy underneath. Needs a small bracket/bar welded on. Can get photos tonight...
Read moreNeed to install additional steel purlins on a commercial building. 12x 150x19 purlins and 24x 200x19 purlins.
Read moreSmall job to weld mid strut on stair rail on an abseiling and climbing structure for Girl Guiding New Zealand.
Read moreNeed replacement metal support rods for foldouts beds. - 4 currently, extra to have on hand depending on the cost Need to be a bit stronger then current parts Also repair of buckled leg on fold out bed. For Girl Guiding New Zealand
Read moreI have a heatpress and a gap has opened up which has caused uneven pressure when we heat press our tshirts only at the top.. this needs to be clamped down. Gapp needs to be closed. Hestpress is 15 x 15 Sorry I dont know proper terminology.. Send me your quote.
Read moreWith over 187,000 reviews in total, and an average rating of 9/10, you can be confident that your job will be handled with the utmost care.
Work carried out by the owner/operator
18th February 2021
Work carried out by the owner/operator
13th January 2021
Work carried out by an employee of the company
29th December 2020
Work carried out by the owner/operator
26th December 2020
Work carried out by the owner/operator
23rd December 2020
Work carried out by the owner/operator
17th December 2020
Work carried out by the owner/operator
6th December 2020
Work carried out by the owner/operator
26th November 2020
Work carried out by an employee of the company
17th November 2020
Work carried out by the owner/operator
20th October 2020
Work carried out by the owner/operator
14th October 2020
Work carried out by the owner/operator
9th October 2020
Work carried out by the owner/operator
28th September 2020
Work carried out by the owner/operator
24th September 2020
Work carried out by the owner/operator
14th September 2020
Work carried out by the owner/operator
2nd September 2020
Work carried out by the owner/operator
31st August 2020