COVID-19: Alert Level 2 allows all trade related business with proper safety protocols. More information here.

Tradies for every job.
Kaitaia to Bluff.
Sorted.

Recent Rodney Fabrication jobs

Check out jobs that others are using Builderscrack to get sorted.

Showing 1 to 18 of 18 jobs
  • Prev
  • |
  • Next

Powdercoating a stainless sink.

Posted 3 days ago

We need a sink powdercoated at home, without removing it.

Read more

Container side open

Posted 2 weeks ago

40ft containter side access open: about 5m wide

Read more

Price for metal Custom Couch risers for Lazyboy lounge suite.

Posted 2 months ago

Hello, I am not sure if this is even a job for this category or whether it's possible. I have a new 3 seater couch and 2.5 seaters. I am in a wheelchair and they are a couple of inches too low for me to easily get off them. I need some foot? risers or something to go under the legs to lift it that don't look hideous. I have looked far and wide and they all seem to be u-g-l-y, junk, don't know if they'd work, or I simply don't know about this stuff. It may be at there is a pair of legs the same...

Read more

Steel rods

Posted 5 months ago

Make steel rods to reinforce concrete

Read more

The Circle

Posted 5 months ago

Building project requires 3 new steel beams to be manufactured and installed.

Read more

Relocation and rebuild

Posted 8 months ago

Take apart steel shed(32 x 8.8m x 5.4mH) at Whenuapai and move to Matakana to rebuild it.

Read more

Residential 3m width driveway 1 in 4 gradient, like a bridge

Posted 9 months ago

Hello! I have a steep slope site in Stanmore Bay, Whangaparaoa. I need to provide driveway access to it. Building timber pole retaining walls is possible, but expensive. My non-NZ registered engineer recommends a different approach... Please see some drawings below. I know how much getting the concrete poured onto metal will cost and even the price of raw metal. But fabricating this will be quite a job... I'd like to get some estimates to see that it is feasible and then proceed with co...

Read more

Cutting windows out of container

Posted 1 year ago

20 foot container need 3 windows cut out , second hand aluminium windows to go in 2 holes. 3rd window will be a flap open of the steel part with struts.

Read more

Quick welding job

Posted 1 year ago

The bracket that holds the accelerator onto the chassis has come free and needs to be welded back on. Vehicle is at my home out the back of Riverhead forest. on the waimaku side. Have attached 3 photos. One photo of the bracket that has come off.one photo of the space where it should be and one photo of me holding the part in place where it should be. Looking for a quick turnaround if possible.

Read more

Security bars for over windows

Posted 1 year ago

Two windows 1.2mt wide by .98cm high require security bars to prevent offenders smashing window and gaining access to retail premises. Substrate is concrete slab. Job is at Jaycar Silverdale next to Repco.

Read more

Steel Frame

Posted 2 years ago

Weld 4 corners of 75x50x4mm mild steel angle to make a square frame. Frame size will be 1m x 0.6m Then weld that frame across 50x50x4mm square tubing ( 2 x 4 welds). Steel is pre-cut with 45 degree mitred corners, weld points cleaned. Can probably drop off anywhere in Auckland

Read more

Tiny house steel frame.

Posted 2 years ago

Steel frame for a tiny house to go on existing trailer 7200mm L x 2400mm W x 3600mm high. I have a scale model to work off but no plans as such.

Read more

Clothesline

Posted 2 years ago

To price and make a aluminium /steel clothes line frame for underneath a outdoor covered in area. Width would have to be approx 4m x 1-1.5m.

Read more

Extension

Posted 2 years ago

extension of wooden house by 12 m x 7 m on concrete floor, steel box section posts and end posts for stacking sliders centre post only on 12 m side, gable roof for sarking, engineered design to come

Read more

Steel Frame Bar Leaner

Posted 2 years ago

We need 1 bar leaner frame made ... then a smaller ...

Read more

Metal Fabrication - Frame Reduction Cut & Weld

Posted 3 years ago

Metal frame needing to be reduced in length. Required 6 cuts, 3 welds to take a middle section out. Weld on the outside will need to be clean/flush ready for powder coating.

Read more

New Steel Framed Workshop Doors

Posted 3 years ago

I need to have two steel framed doors welded up to replace a large rollerdoor. Height of door opening is aprox 4mtrs and the total opening size of these doors is aprox 4mtrs. So each door would be aprox 4mtrs high and 2mtrs wide. Doors will be hinged on the door jams and locked in the middle with a padlock. Covered with roofing iron. Looking for a simple construction/welding job. Nothing fancy or costly. The photo shows the existing rollerdoor. The new doors will come up to just above the light...

Read more

Garage Door and Gate

Posted 3 years ago

Steel frame sectional garage door with custom cladding. And automatic sliding gate. High standard of workmanship required

Read more
Showing 1 to 18 of 18 jobs
  • Prev
  • |
  • Next
Get started now! Post your job for free and find the right tradie. Post your job for free, now!